ASTM A53 – Pipe, Steel, Black and Hot-Dipped, Zinc-Coated, Welded and Seamless
Chemical Compositions（max%）
| Grade | C | Mn | P | S | Cr | Cu | Mo | Ni | V |
| Type S (seamless pipe) | |||||||||
| A | 0.25 | 0.95 | 0.05 | 0.045 | 0.4 | 0.4 | 0.15 | 0.4 | 0.08 |
| B | 0.3 | 1.2 | 0.05 | 0.045 | 0.4 | 0.4 | 0.15 | 0.4 | 0.08 |
| Type E (electric-resistance-welded) | |||||||||
| A | 0.25 | 0.95 | 0.05 | 0.045 | 0.4 | 0.5 | 0.15 | 0.4 | 0.08 |
| B | 0.3 | 1.2 | 0.05 | 0.045 | 0.4 | 0.5 | 0.15 | 0.4 | 0.08 |
| Type F (furnace-welded pipe) | |||||||||
| A | 0.3 | 1.2 | 0.05 | 0.045 | 0.4 | 0.4 | 0.15 | 0.4 | 0.08 |
Note:
The sum of Cu, Ni, Cr, Mo and V shall not exceed 1.00%.
Tensile Requirements (min)
| Grade | Tensile strength psi [MPa] | Yield strength psi [MPa] | Elongation in 2 in. or 50 mm, % |
| A | 48000 [330] | 30000 [205] | (Note 1, 2) |
| B | 60000 [415] | 35000 [240] |
Note:
1)The minimum elongation in 2 in. [50 mm] shall be that determined by the following equation:
e = 625 000 [1940] A0.2/U 0.9
where:
e = minimum elongation in 2 in. or 50 mm in percent, rounded to the nearest percent,
A = the lesser of 0.75 in.2 [500 mm2] and the cross-sectional area of the tension test specimen,
calculated using the specified outside diameter of the pipe, or the nominal width of the tension test specimen and
the specified wall thickness of the pipe, with the calculated value rounded to the nearest 0.01 in.2 [1 mm2], and
U = specified minimum tensile strength, psi [MPa].
2)See below table for the minimum elongation values that are required for various combinations of tension test specimen size and specified minimum tensile strength.
| Area, A, mm2 | Specified Wall Thickness, mm | Elongation in 50 mm, min, % | |||
| Tension Test Specimen | Specified Minimum Tensile Strength, Mpa | ||||
| 19-mm Specimen | 25-mm Specimen | 38-mm Specimen | 330 | 415 | |
| 500 and greater | 26.3 and greater | 20.0 and greater | 13.2 and greater | 36 | 30 |
| 480-499 | 25.3-26.2 | 19.2-19.9 | 12.7-13.1 | 36 | 30 |
| 460-479 | 24.2-25.2 | 18.4-19.1 | 12.1-12.6 | 36 | 29 |
| 440-459 | 23.2-24.1 | 17.6-18.3 | 11.6-12.0 | 36 | 29 |
| 420-439 | 22.1-23.1 | 16.8-17.5 | 11.1-11.5 | 35 | 29 |
| 400-419 | 21.1-22.0 | 16.0-16.7 | 10.6-11.0 | 35 | 29 |
| 380-399 | 20.0-21.0 | 15.2-15.9 | 10.0-10.5 | 35 | 28 |
| 360-379 | 19.0-19.9 | 14.4-15.0 | 9.5-9.9 | 34 | 28 |
| 340-359 | 17.9-18.9 | 13.6-14.3 | 9.0-9.4 | 34 | 28 |
| 320-339 | 16.9-17.8 | 12.8-13.5 | 8.5-8.9 | 34 | 27 |
| 300-319 | 15.8-16.8 | 12.0-12.7 | 7.9-8.4 | 33 | 27 |
| 280-299 | 14.8-15.7 | 11.2-11.9 | 7.4-7.8 | 33 | 27 |
| 260-279 | 13.7-14.7 | 10.4-11.1 | 6.9-7.3 | 32 | 26 |
| 240-259 | 12.7-13.6 | 9.6-10.3 | 6.4-6.8 | 32 | 26 |
| 220-239 | 11.6-12.6 | 8.8-9.5 | 5.8-6.3 | 31 | 26 |
| 200-219 | 10.5-11.5 | 8.0-8.7 | 5.3-5.7 | 31 | 25 |
| 190-199 | 10.0-10.4 | 7.6-7.9 | 5.0-5.2 | 30 | 25 |
| 180-189 | 9.5-9.9 | 7.2-7.5 | 4.8-4.9 | 30 | 24 |
| 170-179 | 9.0-9.4 | 6.8-7.1 | 4.5-4.7 | 30 | 24 |
| 160-169 | 8.4-8.9 | 6.4-6.7 | 4.2-4.4 | 29 | 24 |
| 150-159 | 7.9-8.3 | 6.0-6.3 | 4.0-4.1 | 29 | 24 |
| 140-149 | 7.4-7.8 | 5.6-5.9 | 3.7-3.9 | 29 | 23 |
| 130-139 | 6.9-7.3 | 5.2-5.5 | 3.5-3.6 | 28 | 23 |
| 120-129 | 6.3-6.8 | 4.8-5.1 | 3.2-3.4 | 28 | 23 |
| 110-119 | 5.8-6.2 | 4.4-4.7 | 2.9-3.1 | 27 | 22 |
| 100-109 | 5.3-5.7 | 4.0-4.3 | 2.7-2.8 | 27 | 22 |
| 90-99 | 4.8-5.2 | 3.6-3.9 | 2.4-2.6 | 26 | 21 |
| 80-89 | 4.2-4.7 | 3.2-3.5 | 2.1-2.3 | 26 | 21 |
| 70-79 | 3.7-4.1 | 2.8-3.1 | 1.9-2.0 | 25 | 21 |
| 60-69 | 3.2-3.6 | 2.4-2.7 | 1.6-1.8 | 24 | 20 |
| 50-59 | 2.7-3.1 | 2.0-2.3 | … | 24 | 19 |
| 40-49 | 2.1-2.6 | 1.6-1.9 | … | 23 | 19 |
| 30-39 | 1.6-2.0 | … | … | 22 | 18 |